Solderstep

Solderstep help

Getting started

A sample project (555 oscillator) opens on first launch. Explore it: hover a hole to see its net, click a component to adjust it. A second, multi-board example (power supply and indicator) opens from the welcome screen or the contents of this help.

To start your own: New, then pick the board. The previous project can be restored with Undo (Ctrl+Z).

The left bar holds the tools and components; on the right are the selection, checks, the wiring checklist and the nets. The Connections button opens the view of matings and cables.

Scroll to zoom, right-click or space + drag to pan. C flips between the component side and the (mirrored) copper side.

Boards and templates

The Board templates button opens the editor: size, copper patterns (strips, groups, breadboard style). By hand: Link draws a track between two holes, Unlink removes it, Missing hole removes a hole.

Apply the template to the current board (components are kept) or create a new board with it. To share it or change computer: My library exports your board templates and components in a single file.

Components and palette

Click a component in the list, adjust its parameters, then click on the board to place it. R rotates it. After each placement (component, jumper, solder, pad, cut, label, wire), the tool goes back to selection with the new item selected, ready to adjust or move.

Resistors, diodes, capacitors and LEDs are placed in one click at their usual spacing (set before placing, R to rotate). Then drag either lead to the hole you want, at any distance, even diagonally: the body keeps its size and the leads are drawn to the holes.

References and values place themselves; drag them to move them. A component’s note is shown on the board (Notes button).

Add to my palette saves a configured component (footprint, value, note) so you can place it again in one click. Your library (palette and board templates) is exported and imported as a single file.

Search: type “555”, “jst”, “mini”… above the list; name, value, category and pin names are matched.

Copy and paste: Ctrl+C then Ctrl+V (also from one layout to another), Ctrl+D or Duplicate for an instant copy; references are renumbered.

Modules: three ways, depending on use.

Solder side: a component or jumper can sit under the board (a capacitor under a terminal block, a male header pointing down to plug into an ESP32, a jumper underneath). Place it from the copper-side view (C), or change its side in its properties. Seen from the other side it is dimmed. The checks take it into account (a bare wire on the solder side shorts the strips it crosses; a part may sit under a module on the other side) and the checklist puts it last.

Jumpers, solder and cuts

Jumper (J): click each point, double-click or Enter to finish. Round points are soldered, square ones just pass over; double-click a bend to switch. A bare wire must not touch any other net.

Solder (S): a copper-side solder bridge or trace, drawn the same way.

Solder pad (P): a zone of holes soldered together, with a click or by dragging a rectangle. Several wires can land on it.

Cut (X): click a hole for a drill cut, or between two holes for a knife cut.

Free wire (W): a wire soldered into a hole that goes elsewhere (another board, a free component, or outside the project: motor, battery…). Click the hole, then where it goes. The second click may land on a hole of another board or a free component pin: the wire is joined there; anywhere else, its end stays free, give it a name (“to motor”). The hole counts as connected; a screw terminal takes its wires this way, several per screw if needed.

Eraser (E) deletes what you click. H dims components so you can see and select what is underneath (dimmed components can’t be selected, as in the copper-side view).

Nets, labels and star ground

A net is the set of holes connected together by copper, jumpers and solder. Hover a hole to see it; click a net in the Nets tab to dim everything else.

Label (L) names a net (GND, VCC, SIG…). Two nets with the same name are meant to be connected: the app warns you if they are not. Without a label, a net takes the name of a power pin it touches (GND, 5V, 3V3, VCC…). In a name, write “/” without spaces (TX/RX): “5V / VCC” means a net that carries two names.

Across the assembly: nets join through wires, matings and cables. A net with no name on one board takes the name it has elsewhere (shown with where it comes from), including the name of a power pin of a free component (the GND pin of a jack names the ground).

Star ground: place a solder pad (P) and bring each ground wire to it separately (power, input, output…). Then isolate the GND net in the Nets tab to check that the wires don’t join anywhere else.

The assembly: several boards, free components, wires

An assembly is described with four notions: boards (a plate, its copper and what is soldered on it), free components (on no board: DC jack, panel potentiometer, front-panel LED, cable plug, wired module), soldered wires (from a board hole or a pin to another point) and connections (matings and cables, in the Connections view). To see all this on a simple case: Open the multi-board example, in the contents.

Several boards: the board menu, at the top, adds a board, switches the shown board, renames or removes it. Each board has its own layout and checklist; references (R1, J2…) are unique across the assembly (a duplicate is reported).

Single view: all boards and free components share one view, around the board being edited (the others are dimmed). Click another board to edit it, or one of its items to select it directly; drag a board by its name to move it; double-click to zoom on it (▭: the current board, ⤢: the whole assembly).

Free component: pick it in the palette and drop it outside the boards. Free connector (K) places a generic plug or socket (JST, Dupont, IDC, USB, jack, DIN, XT, GX, RJ…): set its family, gender and pins; it can only be placed off the boards. A free component can be rotated (R), duplicated (Ctrl+D) and added to your palette from its panel. On a free connector, a yellow square marks pin 1.

Wires: with Free wire (W), click a hole, then a free component pin or a hole of another board; anywhere else, the end stays free and gets a name (“to motor”). Click a wire, then drag one of its ends to attach it elsewhere. A ring marks every hole where a wire is soldered. Off-PCB hides free components and wires; on the copper side they are always hidden.

Connections view: matings and cables

The Connections button shows a preview of the boards with only their connectors, in place, plus the free connectors; everything else is dimmed. This is where, and only where, you mate and cable, by dragging a connector onto another (the action is shown while dragging):

A connector takes a single mating or a single cable. Click a cable: its strands are drawn pin to pin, with their net name, and its panel draws the cable’s plugs (the ones that mate with each connector). Click a pin then a pin opposite to add or remove a conductor (crossed cable); Straight cable and Disconnect all act on the pair of ends shown. Del removes the selected mating or cable.

Scroll to zoom, drag the background to pan, ⤢ to see everything again. Boards cannot be moved in this view.

A mating or cable that no longer makes sense (connector deleted, cable without conductors) goes away by itself.

Checks

The Checks tab lists live: components off the board or on a cut hole, holes used twice, shorted pins, ground connected to the supply, differently named nets connected together, reversed electrolytic capacitors and LEDs, components under a module, heatsinks touching a neighbour, bare wires touching, duplicate references.

Voltages: a voltage written explicitly (5V, 3V3, 12V…), on a pin or a label, must be the same everywhere on the net. A generic name (VCC, VDD, VIN) is compatible with any voltage; a ground (GND) must never join a supply.

Whole assembly (several boards, free components): different voltages joined across boards, a ground joined to a supply, conflicting names from one board to another, boards linked without a common ground, matings between connectors of different types or of the same gender.

Click a line to select the items involved. The checks do not replace the schematic: compare with the KiCad schematic (Nets tab).

Unconnected (above the board, or the U key) circles isolated points in magenta: a pin with nothing from outside its own component soldered to its net (another part, jumper, wire; internal links of a pushbutton or module don’t count); a jumper end or wire when nothing else is soldered on the same strip, pad or solder; solder or a solder pad with nothing soldered on it. Handy to spot a missed joint or wire; on a microcontroller, unused pins show up too.

Wiring checklist

The Wiring tab lists everything to fit in the usual order: cuts, jumpers, low components, then ICs, capacitors, connectors and modules, and finally the copper-side solder (bridges, traces, pads), which often reuses component leads.

Tick items as you go; Dim not placed fades on the board what is still to be fitted: you see the board come together step by step. Progress is saved with the project.

Folded leads: a solder trace starting at a lead of a resistor, diode, LED, capacitor or a jumper end can be made with a folded lead: in the inspector, choose which one among those at its ends (“Lead R1.2 folded”, “… of the jumper B4 → B9”). A lead serves only one trace. It is drawn as a wire and listed “Fold lead R1.2” right after the component is fitted; a warning tells you if the lead is probably too short. The wire length to cut for each jumper is shown, copper-side part included.

Bill of materials (button in the Wiring tab): the parts of the whole project grouped by type and value, with references, location and solder side, then the supplies (boards, jumper wire, cuts, wires, cables). Export it as CSV for a spreadsheet, or print it (or save it as PDF from the print dialog). The Assembly report button gathers, for each board, both sides, its checklist (tick boxes for a pen) and its checks, then the connections, the project-wide checks and the bill of materials: one board per page, to print or save as PDF.

KiCad netlist and schematic

KiCad netlist produces a .net file you can import into KiCad to compare with a schematic.

Compare with schematic (Nets tab): import the netlist exported by KiCad (File → Export → Netlist, KiCad format). The Checks then report missing or extra connections, parts present on only one side and differing values. Parts are matched by reference; pins by name when the schematic gives one (A/K of a diode, E/B/C of a transistor), otherwise by number. The schematic is saved with the project: the comparison updates with every change.

Several boards: the exported netlist and the comparison cover the whole assembly. Components of every board are matched by reference (unique across the project) and nets are joined through connections and cables: a single KiCad schematic for the whole assembly compares directly. If the schematic only covers one board, the others are simply reported as absent.

Saving and files

The current project, your board templates and your palette are kept in the browser. They stay on this device and are lost if you clear the site’s data.

Save downloads the project as a .json file; Open loads it back. Keep a copy of your important projects.

📱 Phone sends the layout as a link (AirDrop, Messages, email…): opened on the phone, it shows the layout read-only for the bench (component and copper views, wiring checklist, nets). One finger pans, two fingers zoom, tapping a hole isolates its net; the screen stays on. Boxes ticked on the phone stay on the phone.

Shortcuts

About

Solderstep is a free tool, with no ads and no account. Version 0.4.0-beta.0.

No cookies. Your projects stay in your browser; nothing is sent to a server.

A remark, a bug, an idea? Write to me.

Free and ad-free: a coffee (or a beer) keeps it going.

Legal notice

Publisher: blue3eight
Contact: blue3eight@gmail.com
Host: Cloudflare, Inc., 101 Townsend St, San Francisco, CA 94107, USA